|
KLAMPTITE® RIVET Fastening
System
Structural
External locking feature
for Structural Klamptite® requires special nosetip.
Provides good vibration resistance. Exceptional clamp-up
strength. Wide grip range.
Three-leg formation compensates for oversized or irregular holes.
Benefits
Technical Information
Order Samples
Benefits
- Visible Lock: When
using the prescribed nosetip, the rivet stem and body are
physically and visibly locked. This allows inspection of
the lock, ensuring a quality fastened joint. Good
vibration resistance.
- Grip Tolerant: Will
fasten materials over a wide range of sheet thicknesses.
- Sealing Capability: With
the use of an optional rubber washer, this fastener can
be made to effect a weather-resistant seal.
- Hole Preparation: The
three legs of the Klamptite rivet provide a large
blind-side bearing surface over which to distribute
loads.
Technical
Information
Structural
Nom. Rivet Diam.
|
Hole Size
|
Drill Number
|
S Stem Diam.
|
D Sleeve Diam.
|
Protruding Head
|
Countersunk Head
|
A Head Diam.
|
B Head Thick.
|
A Head Diam.
|
B Head Thick.
|
| (6) 3/16" (4,8mm) |
.204-.209" (5,18-5,31) |
#5 |
.103 (2,62) |
.197 (5,00) |
.445 (11,30) |
.088 (2,24) |
.335 (8,51) |
.070 (1,78) |
| (8) 1/4" (6,4mm) |
.252-.262" (6,40-6,65) |
F |
.136 (3,45) |
.242 (6,15) |
.560 (14,22) |
.113 (2,87) |
|
|
*Shear
and tensile values are those to be typically
expected. Retention values are the minimum to be
expected when installed properly.
Rivet Diam.
|
BA Series
Aluminum Body
Aluminum Stem lbs. f (N)
|
Shear
|
Tensile
|
Stem Retention*
|
| (6) 3/16" (4,8mm) |
700 (3113) |
450 (2001) |
50 (222) |
| (8) 1/4" (6,4mm) |
1350 (6004) |
1000 (4447) |
100 (445) |
NOTE:
L & E dimensions vary with each grip length.
(See the "Part Selection" table below.)
Rivet Diam.
|
G
Rivet Grip Range
|
L
Rivet Length Max.
|
E
Blind Length Max.
|
Series BA
Aluminum Rivet Aluminum Stem
|
Inch
|
mm.
|
Inch
|
mm.
|
Inch
|
mm.
|
Prtrd. Head
|
Ctsk. Head
|
| 3/16" (4,8mm) (6) |
.050-.250 |
1,27-6,35 |
.890 |
22,61 |
1.21 |
30,74 |
BAPKTR-06-04 |
|
| .187-.375 |
4,75-9,53 |
.985 |
25,02 |
1.30 |
33,02 |
BAPKTR-06-06 |
BACKTR-06-06 |
| .375-.562 |
9,53-14,27 |
1.12 |
28,45 |
1.43 |
36,32 |
BAPKTR-06-09 |
|
| .562-.750 |
14,27-19,05 |
1.30 |
33,02 |
1.62 |
41,15 |
BAPKTR-06-12 |
BACKTR-06-12 |
| 1/4" (6,4mm) (8) |
.060-.250 |
1,52-6,35 |
.925 |
23,50 |
1.30 |
33,02 |
BAPKTR-08-04 |
|
| .187-.375 |
4,75-9,53 |
1.05 |
26.67 |
1.42 |
36,07 |
BAPKTR-08-06 |
|
NOTE:
The structural Klamptite® rivet must always be
installed using nosetip number 743C53 or 743C51
for 3/16" and 1/4" diameters,
respectively. The pulling head of the
installation tool should incorporate a 3-jaw
system.
NOTES:
- Items listed
on these pages reflect our manufacturing capability.
- Finishes:
aluminum stems, and rivets are coated with a wax
lubricant.
- Weather
resistance can be obtained by specifying a synthetic
rubber washer under protruding head fasteners (i.e..
BAPKTR-6W6)
Non-Structural 
Provides good vibration
resistance. Exceptional clamp-up strength. Wide grip range.
Benefits:
- Grip Tolerant: Will
fasten materials over a wide range of sheet thicknesses.
- Hole Preparation: The
three legs of the Klamptite rivet provide a large
blind-side bearing surface over which to distribute
loads.
- No Special Nose tip: No
special nose tip required for non-structural Klamptite.
Rivet Diam.
|
BA Series
Aluminum Body
Aluminum Stem lbs. f (N)
|
Shear
|
Tensile
|
| 3/16" (4,8mm) |
290 (1290) |
380 (1690) |
| 1/4" (6,4mm) |
450 (2001) |
575 (2557) |
Nom. Rivet Diam.
|
Hole Size
|
Drill Number
|
S Stem Diam.
|
D Sleeve Diam.
|
Protruding Head
|
Countersunk Head
|
A Head Diam.
|
B Head Thick.
|
A Head Diam.
|
B Head Thick
|
| 3/16" (4,8mm) |
.204-.209 (5,18-5,31) |
#5 |
.114 (2,90) |
.198 (5,03) |
.445 (11,30) |
.088 (2,24) |
.335 (8,57) |
.070 (1,79) |
| 1/4" (6,4mm) |
.252-.262 (6,40-6,65) |
F |
.151 (3,84) |
.242 (6,15) |
.560 (14,22) |
.113 (2,87) |
|
|
Note:
L & E dimensions vary with each grip length.
(See the "Part Selection" table below.)
Rivet Diam.
|
G Rivet Grip
Range
|
L Rivet Length
Max.
|
E Blind Length
Max.
|
BA Series
Aluminum Rivet Aluminum Stem
|
Protruding Head
|
Ctsk. Head
|
| 3/16"(6) (4,8mm) |
.050-.250 (1.27-6.35) |
.890 (22.61) |
1.0 (25.40) |
BAPK-64 |
|
| .187-.375 (4.75-9.53) |
.985 (25.02) |
1.095 (27.81) |
BAPK-66 |
BACK-66 |
| .375-.562 (9.53-14.27) |
1.118 (28.40) |
1.218 (30.94) |
BAPK-69 |
|
| .562-.750 (14.27-19.05) |
1.296 (32.92 |
1.400 (35.56) |
BAPK-612 |
BACK-612 |
| 1/4"(8) (6,4mm) |
.060-.250 (1.52-6.35) |
.925 (23.50) |
1.042 (26.47) |
BAPK-84 |
|
| .187-.375 (4.75-9.53) |
1.050 (26.67) |
1.167 (29.64) |
BAPK-86 |
|
NOTES:
Items
listed on these pages reflect our manufacturing
capability.
Finishes:
aluminum stems, and rivets are coated with a wax
lubricant.
|
